The right Spark Plug

[azi malik]

Installing spark plugs

Spark_Plug-198x300.jpg (18.61 KiB) Viewed 4209 times

Torque is one of the most critical aspects of spark plug installation. Torque directly affects the spark plugs’ ability to transfer heat out of the combustion chamber. A spark plug that is under-torqued will not be fully seated on the cylinder head, hence heat transfer will be slowed. This will tend to elevate combustion chamber temperatures to unsafe levels, and pre-ignition and detonation will usually follow. Serious engine damage is not far behind.
An over-torqued spark plug can suffer from severe stress to the Metal Shell which in turn can distort the spark plug’s inner gas seals or even cause a hairline fracture to the spark plug’s insulator…in either case, heat transfer can again be slowed and the above mentioned conditions can occur.

The spark plug holes must always be cleaned prior to installation, otherwise you may be torquing against dirt or debris and the spark plug may actually end up under-torqued, even though your torque wrench says otherwise. Of course, you should only install spark plugs in a cool engine, because metal expands when its hot and installation may prove difficult.

Gapping

Since the gap size has a direct affect on the spark plug’s tip temperature and on the voltage necessary to ionize (light) the air/fuel mixture, careful attention is required. While it is a popular misconception that plugs are pre-gapped from the factory, the fact remains that the gap must be adjusted for the vehicle that the spark plug is intended for. Those with modified engines must remember that a modified engine with higher compression or forced induction will typically require a smaller gap settings (to ensure ignitability
in these denser air/fuel mixtures). As a rule, the more power you are making, the smaller the gap you will need.
A spark plug’s voltage requirement is directly proportionate to the gap size. The larger the gap, the more voltage is needed to bridge the gap. Most experienced tuners know that opening gaps up to present a larger spark to the air/fuel mixture maximizes burn efficiency. It is for this reason that most racers add high power ignition systems. The added power allows them to open the gap yet still provide a strong spark.
With this mind, many think the larger the gap the better. In fact, some aftermarket ignition systems boast that their systems can tolerate gaps that are extreme. Be wary of such claims. In most cases, the largest gap you can run may still be smaller than you think.

Indexing

This is for racers only. Indexing refers to a process whereby auxiliary washers of varying thickness are placed under the spark plug’s shoulder so that when the spark plug is tightened, the gap will point in the desired direction.

However, without running an engine on a dyno, it is impossible to gauge which type of indexing works best in your engine. While most engines like the spark plug’s gap open to the intake valve, there are still other combinations that make more power with the gap pointed toward the exhaust valve.

In any case, engines with indexed spark plugs will typically make only a few more horsepower, typically less than 1% of total engine output. For a 500hp engine, you’d be lucky to get 5hp. While there are exceptions, the bottom line is that without a dyno, gauging success will be difficult.

Heat Range selection

Let’s make this really simple: when you need your engine to run a little cooler, run a colder plug. When you need your engine to run a little hotter, run a hotter spark plug. However, FAIRSALE AUTOS strongly cautions people that going to a hotter spark plug can sometimes mask a serious symptom of another problem that can lead to engine damage. Be very careful with heat ranges. Seek professional guidance if you are unsure.

With modified engines (those engines that have increased their compression) more heat is a by-product of the added power that normally comes with increased compression. In short, select one heat range colder for every 75-100 hp you add, or when you significantly raise compression. Also remember to retard the timing a little and to increase fuel enrichment and octane. These tips are critical when adding forced induction (turbos, superchargers or nitrous kits), and failure to address ALL of these areas will virtually guarantee engine damage.

An engine that has poor oil control can sometimes mask the symptom temporarily by running a slightly hotter spark plug. While this is a “Band-Aid” approach, it is one of the only examples of when and why one would select
a hotter spark plug.
Using “racing” spark plugs

Be cautious! In reality, most “racing” spark plugs are just colder heat ranges of the street versions of the spark plug. They don’t provide any more voltage to the spark plug tip! Their internal construction is no different than most standard spark plugs.

So many young enthusiasts are wasting their precious money on Iridum / Platinum Plugs and Splitfire Plugs and plugwires, when in fact these would not increase the performance of their ‘normal’ and ‘unmodified’ vehicles in any manner whatsoever.

Whenever a customer, especially young dare devils come to us for buying spark plugs, we always ask them the details of their vehicle and if we feel that the customer is making a mistake and wasting his money, we always advise him not to do so even if it is to our own disadvantage and loss.

Like the person who installed iridum plugs in his Honda Civic 95, but could not enjoy the value for his precious money spent. Whereas, he could have had a much better return, had he installed simple four point plugs (preferably Lucas). Always ask a person who ‘knows’ the technicalities of spark plugs and only then go and spend your (or your parent’s) hard earned money.

For plug wires, we see that people are wasting thousands of rupees to buy Splitfire and other plug wires for unmodified and stock vehicles. Total wastage. Go for silicon plug wire (preferably American) altered by the seller for your vehicles wire size requirements. A typical American Silicon Plug Wire set with American boots and American terminals costs between Rs. 500 to Rs. 700 and lasts four to five times longer than other Japanese normal wires.

There are some exceptions, though. Extremely high compression cars or those running exotic fuels will have different spark plug requirements and are supplied spark plugs that are well-suited for these requirements. They are classified as “specialized spark plugs for racing applications”. Some are built with precious metal alloy tips for greater durability and the ability to fire in denser or leaner air/fuel mixtures.

However, installing the same spark plugs Kenny Bernstein uses in his 300+ mph Top Fuel car (running Nitromethane at a 2:1 air/fuel ratio and over 20:1 dynamic compression) in your basically stock Honda Civic (running 15:1 a/f ratios with roughly 9.5:1 compression) will do nothing for you! In fact, since Kenny’s plugs are fully 4 heat ranges colder, they’d foul out in your Honda in just a few minutes.

I try to tell people that are looking to “screw in” some cheap horsepower that, in most cases, spark plugs are not the answer.

To be blunt, when experienced tuners build race motors, they select their spark plugs for different reasons: to remove heat more efficiently, provide sufficient spark to completely light all the air/fuel mixture, to survive the added stresses placed upon a high performance engine’s spark plugs, and to achieve optimum piston-to-plug clearance.

Some of these “specialized racing plugs” are made with precious metal alloy center/ground electrodes or fine wire tips or retracted-nose insulators. Again, these features do not necessarily mean that the spark plug will allow the engine to make more power, but these features are what allow the spark plug to survive in these tortuous conditions. Most racers know screwing in a new set of spark plugs will not magically “unlock” hidden horsepower.

Using high power ignition systems

Many of the more popular aftermarket ignition systems are of the capacitive discharge type. They store voltage, or accumulate it, until a point at which a trigger signal allows release of this more powerful spark. Companies like Mallory, MSD, Crane and Accel, to name a few, offer such systems.

They affect spark plugs in that they allow the gaps to be opened up to take advantage of the increased capacity. The theory is that the larger and the more intense the spark you are able to present to the air/fuel mixture, the more likely you will be to burn more fuel, and hence the more power you will make.

We encourage the use of such systems, but only on modified or older non-computer controlled vehicles.
In reality, computer controlled vehicles do such a good job of lighting off the air/fuel mixture (as evidenced by the ultra-low emissions), added ignition capacity would do little to burn more fuel since the stock configuration is doing such a good job. Older non-computer controlled vehicles or those that have been modified with higher compression or boosted (nitrous, turbo, supercharged) engines can certainly take advantage of a more powerful ignition system.

[matt-lee]

hi any my friends,

am matt from china company.

we can offer oil filter, fuel filter, air fliter, brake drum , brake disc, clutch cove, clutch disc, oil seals and so on.

anyone want to buy from china ,may contact me.
matt16688@gmail.com